A

Back to top

B

Back to top

C

Back to top

D

Back to top

E

Back to top

F

Back to top

G

GF C I, or G F I	Ground Fault Circuit Interrupter  an ultra sensitive plug designed to shut off all electric current. Used in bathrooms, kitchens, exterior waterproof outlets, garage outlets, and "wet areas". Has a small reset button on the plug.
Gable	The end, upper, triangular area of a home, beneath the roof.
Gang nail plate	A steel plate attached to both sides at each joint of a truss. Sometimes called a fishplate or gussett.
Gate valve	A valve that lets you completely stop—but not modulate—the flow within a pipe.
General Contractor	A contractor who enters into a contract with the owner of a project for the construction of the project and who takes full responsibility for its completion, although the contractor may enter into subcontracts with others for the performance of specific parts or phases of the project.
Gas lateral	The trench or area in the yard where the gas line service is located, or the work of installing the gas service to a home.
Girder	A large or principal beam of wood or steel used to support concentrated loads at isolated points along its length.
Glazing	The process of installing glass, which commonly is secured with glazier's points and glazing compound.
Globe valve	A valve that lets you adjust the flow of water to any rate between fully on and fully off. Also see gate valve.
Gloss enamel	A finishing paint material. Forms a hard coating with maximum smoothness of surface and dries to a sheen or luster (gloss)
Glued Laminated Beam (Glulam)	A structural beam composed of wood laminations or lams. The lams are pressure bonded with adhesives to attain a typical thickness of 1 ½" . (It looks like 5 or more 2 X 4's are glued together).
Grade	Ground level, or the elevation at any given point. Also the work of leveling dirt. Also the designated quality of a manufactured piece of wood.
Grade beam	A foundation wall that is poured @ level with or just below the grade of the earth. An example is the area where the 8' or 16' overhead garage door "block out" is located, or a lower (walk out basement) foundation wall is poured
Graduated Payment Mortgage (GPM)	A fixedrate, f ixed schedule loan. It starts with lower payments than a level payment loan; payments rise annually, with the entire increase being used to reduce the outstanding balance. The increase in payments may enable the borrower to pay off a 30 year loan in 15 to 20 years, or less.
Grain	The direction, size, arrangement, appearance, or quality of the fibers in wood.
Grid	The completed assembly of main and cross tees in a suspended ceiling system before the ceiling panels are installed. Also the decorative slats (munton) installed between glass panels.
Ground	Refers to electricity's habit of seeking the shortest route to earth. Neutral wires carry it there in all circuits. An additional grounding wire or the sheathing of the metal clad cable or conduit—protects against shock if the neutral leg is interrupted.
Ground fault	Ground Fault Circuit Interrupter (GFCI, GFI)  an ultra sensitive plug designed to shut off all electric current. Used in bathrooms, kitchens, exterior waterproof outlets, garage outlets, and "wet areas". Has a small reset button on the plug.
Ground iron	The plumbing drain and waste lines that are installed beneath the basement floor. Cast iron was once used, but black plastic pipe (ABS) is now widely used.
Groundwater	Water from an aquifer or subsurface water source.
Grout	A wet mixture of cement, sand and water that flows into masonry or ceramic crevices to seal the cracks between the different pieces. Mortar made of such consistency (by adding water) that it will flow into the joints and cavities of the masonry work and fill them solid.
Gusset	A flat wood, plywood, or similar type member used to provide a connection at the intersection of wood members. Most commonly used at joints of wood trusses. They are fastened by nails, screws, bolts, or adhesives.
Gutter	A shallow channel or conduit of metal or wood set below and along the (fascia) eaves of a house to catch and carry off rainwater from the roof.
Gyp board	Drywall. Wall board or gypsum.  A panel (normally 4' X 8', 10', 12', or 16')made with a core of Gypsum (chalk like) rock, which covers interior walls and ceilings.
Gypsum plaster	Gypsum formulated to be used with the addition of sand and water for base coat plaster

Back to top

H

H Clip	Small metal clips formed like an "H" that fits at the joints of two plywood (or wafer board) sheets to stiffen the joint. Normally used on the roof sheeting.
Hardware	All of the "metal" fittings that go into the home when it is near completion. For example, door knobs, towel bars, handrail brackets, closet rods, house numbers, door closers, etc. The Interior Trim Carpenter installs the "hardware".
Haunch	An extension, knee like protrusion of the foundation wall that a concrete porch or patio will rest upon for support.
Hazard insurance	Protection against damage caused by fire, windstorms, or other common hazards. Many lenders require borrowers to carry it in an amount at least equal to the mortgage.
Header	(a) A beam placed perpendicular to joists and to which joists are nailed into  framing for a chimney, stairway, or other opening. (b) A wood lintel. (c) The horizontal structural member over an opening (for example over a door or window).
Hearth	The fireproof area directly in front of a fireplace. The inner or outer floor of a fireplace, usually made of brick, tile, or stone.
Heating load	The amount of heating required to keep a building at a specified temperature during the winter, usually 65° F, regardless of outside temperature.
Heat meter	An electrical municipal inspection of the electric meter breaker panel box.
Heat pump	A mechanical device which uses compression and decompression of gas to heat and/or cool a house.
Heat Rough	Work performed by the Heating Contractor after the stairs and interior walls are built. This includes installing all duct work and flue pipes. Sometimes, the furnace and fireplaces are installed at this stage of construction.
Heat Trim	Work done by the Heating Contractor to get the home ready for the municipal Final Heat Inspection. This includes venting the hot water heater, installing all vent grills, registers, air conditioning services, turning on the furnace, installing thermostats, venting ranges and hoods, and all other heat related work.
Heel cut	A notch cut in the end of a rafter to permit it to fit flat on a wall and on the top, doubled, exterior wall plate.
Highlights	A light spot, area, or streak on a painted surface.
Hip	A roof with four sloping sides. The external angle formed by the meeting of two sloping sides of a roof.
Hip roof	A roof that rises by inclined planes from all four sides of a building.
Home run (electrical)	The electrical cable that carries power from the main circuit breaker panel to the first electrical box, plug, or switch in the circuit.
Honey combs	The appearance concrete makes when rocks in the concrete are visible and where there are void areas in the foundation wall, especially around concrete foundation windows.
Hose bib	An exterior water faucet (sill cock).
Hot wire	The wire that carries electrical energy to a receptacle or other device in contrast to a neutral, which carries electricity away again. Normally the black wire. Also see ground.
Humidifier	An appliance normally attached to the furnace, or portable unit device designed to increase the humidity within a room or a house by means of the discharge of water vapor.
Hurricane clip	Metal straps that are nailed and secure the roof rafters and trusses to the top horizontal wall plate. Sometimes called a Teco clip.
H V A C	An abbreviation for Heat, Ventilation, and Air Conditioning

Back to top

 I

 

I-beam	A steel beam with a cross section resembling the letter I. It is used for long spans as basement beams or over wide wall openings, such as a double garage door, when wall and roof loads bear down on the opening.
I-joist	Manufactured structural building component resembling the letter "I". Used as floor joists and rafters. I joists include two key parts: flanges and webs. The flange of the I joist may be made of laminated veneer lumber or dimensional lumber, usually formed into a 1 ½" width. The web or center of the I-joist is commonly made of plywood or oriented strand board (OSB). Large holes can be cut in the web to accommodate duct work and plumbing waste lines. I- joists are available in lengths up to 60 feet long
Incandescent lamp	A lamp employing an electrically charged metal filament that glows at white heat. A typical light bulb.
Index	The interest rate or adjustment standard that determines the changes in monthly payments for an adjustable rate loan.
Infiltration	The passage of air from indoors to outdoors and vice versa; term is usually associated with drafts from cracks, seams or holes in buildings.
Inside corner	The point at which two walls form an internal angle, as in the corner of a room.
Insulating glass	Window or door in which two panes of glass are used with a sealed air space between.  Also known as Double glass.
Insulation board, rigid	A structural building board made of coarse wood or cane fiber in ½" and 25/32 inch thickness. It can be obtained in various size sheets and densities.
Insulation	Any material high in resistance to heat transmission that, when placed in the walls, ceiling, or floors of a structure, and will reduce the rate of heat flow.
Interest	The cost paid to a lender for borrowed money.
Interior finish	Material used to cover the interior framed areas of walls and ceilings
Irrigation	Lawn sprinkler system

Back to top

J

 

J Channel	Metal edging used on drywall to give the edge a better finished appearance when a wall is not "wrapped" Generally, basement stairway walls have drywall only on the stair side. J Channel is used on the vertical edge of the last drywall sheet
Jack post	A type of structural support made of metal, which can be raised or lowered through a series of pins and a screw to meet the height required. Basically used as a replacement for an old supporting member in a building. See Monopost.
Jack rafter	A rafter that spans the distance from the wall plate to a hip, or from a valley to a ridge.
Jamb	The side and head lining of a doorway, window, or other opening. Includes studs as well as the frame and trim.
Joint	The location between the touching surfaces of two members or components joined and held together by nails, glue, cement, mortar, or other means.
Joint cement or Joint compound	A powder that is usually mixed with water and used for joint treatment in gypsum-wallboard finish. Often called "spackle" or drywall mud.
Joint tenancy	A form of ownership in which the tenants own a property equally. If one dies, the other automatically inherits the entire property.
Joint trench	When the electric company and telephone company dig one trench and "drop" both of their service lines in.
Joist	Wooden 2 X 8's, 10's, or 12's that run parallel to one another and support a floor or ceiling, and supported in turn by larger beams, girders, or bearing walls.
Joist hanger	A metal "U" shaped item used to support the end of a floor joist and attached with hardened nails to another bearing joist or beam.
Jumpers	Water pipe installed in a water meter pit (before the water meter is installed), or electric wire that is installed in the electric house panel meter socket before the meter is installed. This is sometimes illegal

Back to top

K

Back to top

L

Laminated shingles	Shingles that have added dimensionality because of extra layers or tabs, giving a shake-like appearance. May also be called "architectural shingles" or "three dimensional shingles."
Laminating	Bonding together two or more layers of materials.
Landing	A platform between flights of stairs or at the termination of a flight of stairs. Often used when stairs change direction. Normally no less than 3 ft. X 3 ft. square.
Lap	To cover the surface of one shingle or roll with another.
Latch	A beveled metal tongue operated by a spring-loaded knob or lever. The tongue's bevel lets you close the door and engage the locking mechanism, if any, without using a key. Contrasts with dead bolt.
Lateral (electric, gas, telephone, sewer and water)	The underground trench and related services (i.e., electric, gas, telephone, sewer and water lines) that will be buried within the trench.
Lath	A building material of narrow wood, metal, gypsum, or insulating board that is fastened to the frame of a building to act as a base for plaster, shingles, or tiles.
Lattice	An open framework of criss-crossed wood or metal strips that form regular, patterned spaces.
Ledger (for a Structural Floor)	The wooden perimeter frame lumber member that bolts onto the face of a foundation wall and supports the wood structural floor.
Ledger strip	A strip of lumber nailed along the bottom of the side of a girder on which joists rest.
Leech field	A method used to treat/dispose of sewage in rural areas not accessible to a municipal sewer system.  Sewage is permitted to be filtered and eventually discharged into a section of the lot called a leech field.
Let-in brace	Nominal 1 inch- thick boards applied into notched studs diagonally. Also, an "L" shaped, long (@ 10') metal strap that are installed by the framer at the rough stage to give support to an exterior wall or wall corner.
Level	True horizontal. Also a tool used to determine level.
Level Payment Mortgage	A mortgage with identical monthly payments over the life of the loan.
Lien	An encumbrance that usually makes real or personal property the security for payment of a debt or discharge of an obligation.
Light	Space in a window sash for a single pane of glass. Also, a pane of glass.
Limit switch	A safety control that automatically shuts off a furnace if it gets too hot. Most also control blower cycles.
Lineal foot	A unit of measure for lumber equal to 1 inch thick by 12 inches wide by 12 inches long. Examples: 1" x 12" x 16' = 16 board feet, 2" x 12" x 16' = 32 board feet.
Lintel	A horizontal structural member that supports the load over an opening such as a door or window.
Load bearing wall	Includes all exterior walls and any interior wall that is aligned above a support beam or girder. Normally, any wall that has a double horizontal top plate.
Loan	The amount to be borrowed.
Loan to value ratio	The ratio of the loan amount to the property valuation and expressed as a percentage. E.g. if a borrower is seeking a loan of $200,000 on a property worth $400,000 it has a 50% loan to value rate. If the loan were $300,000, the LTV would be 75%. The higher the loan to value, the greater the lender's perceived risk. Loans above normal lending LTV ratios may require additional security.
Lookout	A short wood bracket or cantilever that supports an overhang portion of a roof.
Louver	A vented opening into the home that has a series of horizontal slats and arranged to permit ventilation but to exclude rain, snow, light, insects, or other living creatures.
Lumens	Unit of measure for total light output. The amount of light falling on a surface of one square foot.

Back to top

M

 

Male	Any part, such as a bolt, designed to fit into another (female) part. External threads are male.
Mantel	The shelf above a fireplace opening. Also used in referring to the decorative trim around a fireplace opening.
Manufactured wood	A wood product such as a truss, beam, gluelam, microlam or joist which is manufactured out of smaller wood pieces and glued or mechanically fastened to form a larger piece. Often used to create a stronger member which may use less wood. See also Oriented Strand Board.
Manufacturer's specifications	The written installation and/or maintenance instructions which are developed by the manufacturer of a product and which may have to be followed in order to maintain the product warrantee.
Masonry	Stone, brick, concrete, hollowtile, concrete block, or other similar building units or materials. Normally bonded together with mortar to form a wall.
Mastic	A pasty material used as a cement (as for setting tile) or a protective coating (as for thermal insulation or waterproofing)
Mechanics lien	A lien on real property, created by statue in many years, in favor of persons supplying labor or materials for a building or structure, for the value of labor or materials supplied by them. In some jurisdictions, a mechanics lien also exists for the value of professional services. Clear title to the property cannot be obtained until the claim for the labor, materials, or professional services is settled. Timely filing is essential to support the encumbrance, and prescribed filing dates vary by jurisdiction.
Metal lath	Sheets of metal that are slit to form openings within the lath. Used as a plaster base for walls and ceilings and as reinforcing over other forms of plaster base.
Microlam	A manufactured structural wood beam. It is constructed of pressure and adhesive bonded wood strands of wood. They have a higher strength rating than solid sawn lumber. Normally comes in l ½" thickness' and 9 ½", 11 ½" and 14" widths
Milar (mylar)	Plastic, transparent copies of a blueprint.
Millwork	Generally all building materials made of finished wood and manufactured in millwork plants. Includes all doors, window and door frames, blinds, mantels, panelwork, stairway components (ballusters, rail, etc.), moldings, and interior trim. Does not include flooring, ceiling, or siding.
Miter joint	The joint of two pieces at an angle that bisects the joining angle. For example, the miter joint at the side and head casing at a door opening is made at a 45° angle.
Molding	A wood strip having an engraved, decorative surface.
Monopost	Adjustable metal column used to support a beam or bearing point. Normally 11 gauge or Schedule 40 metal, and determined by the structural engineer
Mortar	A mixture of cement (or lime) with sand and water used in masonry work.
Mortgage	Loan secured by land.
Mortgage broker	A broker who represents numerous lenders and helps consumers find affordable mortgages; the broker charges a fee only if the consumer finds a loan.
Mortgage company	A company that borrows money from a bank, lends it to consumers to buy homes, then sells the loans to investors.
Mortgage deed	Legal document establishing a loan on property.
Mortgagee	The lender who makes the mortgage loan.
Mortgage loan	A contract in which the borrower's property is pledged as collateral. It is repaid in installments. The mortgagor (buyer) promises to repay principal and interest, keep the home insured, pay all taxes and keep the property in good condition.
Mortgage Origination Fee	A charge for work involved in preparing and servicing a mortgage application (usually one percent of the loan amount).
Mortise	A slot cut into a board, plank, or timber, usually edgewise, to receive the tenon (or tongue) of another board, plank, or timber to form a joint.
Mudsill	Bottom horizontal member of an exterior wall frame which rests on top a foundation, sometimes called sill plate. Also sole plate, bottom member of interior wall frame.
Mullion	A vertical divider in the frame between windows, doors, or other openings.
Muntin	A small member which divides the glass or openings of sash or doors.
Muriatic acid	Commonly used as a brick cleaner after masonry work is completed.
Mushroom	The unacceptable occurrence when the top of a caisson concrete pier spreads out and hardens to become wider than the foundation wall thickness

Back to top

N

 

Nail inspection	An inspection made by a municipal building inspector after the drywall material is hung with nails and screws (and before taping).
Natural finish	A transparent finish which does not seriously alter the original color or grain of the natural wood. Natural finishes are usually provided by sealers, oils, varnishes, water repellent preservatives, and other similar materials.
NEC (National Electrical Code)	A set of rules governing safe wiring methods. Local codes which are backed by law may differ from the NEC in some ways.
Neutral wire	Usually color coded white, this carries electricity from an outlet back to the service panel. Also see hot wire and ground.
Newel post	The large starting post to which the end of a stair guard railing or balustrade is fastened.
Nonbearing wall	A wall supporting no load other than its own weight.
Nosing	The projecting edge of a molding or drip or the front edge of a stair tread.
Notch	A crosswise groove at the end of a board.
Note	A formal document showing the existence of a debt and stating the terms of repayment.
Nozzle	The part of a heating system that sprays the fuel of fuel air mixture into the combustion chamber.

Back to top

O

 

O C-On Center	The measurement of spacing for studs, rafters, and joists in a building from the center of one member to the center of the next.
Oakum	Loose hemp or jute fiber that's impregnated with tar or pitch and used to caulk large seams or for packing plumbing pipe joints
Open hole inspection	When an engineer (or municipal inspector) inspects the open excavation and examines the earth to determine the type of foundation (caisson, footer, wall on ground, etc.) that should be installed in the hole.
Oriented Strand Board or OSB	A manufactured 4' X 8' wood panel made out of 1" - 2" wood chips and glue. Often used as a substitute for plywood.
Outrigger	An extension of a rafter beyond the wall line. Usually a smaller member nailed to a larger rafter to form a cornice or roof overhang.
Outside corner	The point at which two walls form an external angle, one you usually can walk around.
Overhang	Outward projecting soffit area of a roof; the part of the roof that hangs out or over the outside wall. See also Cornice.

Back to top

P

Padding	A material installed under carpet to add foot comfort, isolate sound, and to prolong carpet life.
Pad out, pack out	To shim out or add strips of wood to a wall or ceiling in order that the finished ceiling/wall will appear correct.
Paint	A combination of pigments with suitable thinners or oils to provide decorative and protective coatings. Can be oil based or latex water based.
Pallets	Wooden platforms used for storing and shipping material. Forklifts and hand trucks are used to move these wooden platforms around.
Panel	A thin flat piece of wood, plywood, or similar material, framed by stiles and rails as in a door (or cabinet door), or fitted into grooves of thicker material with molded edges for decorative wall treatment.
Paper, building	A general term for papers, felts, and similar sheet materials used in buildings without reference to their properties or uses. Generally comes in long rolls.
Parapet	A wall placed at the edge of a roof to prevent people from falling off.
Parting stop or strip	A small wood piece used in the side and head jambs of double hung windows to separate the upper sash from the lower sash.
Particle board	Plywood substitute made of course sawdust that is mixed with resin and pressed into sheets. Used for closet shelving, floor underlayment, stair treads, etc.
Partition	A wall that subdivides spaces within any story of a building or room.
Paver, paving	Materials—commonly masonry—laid down to make a firm, even surface.
Payment schedule	A pre- agreed upon schedule of payments to a contractor usually based upon the amount of work completed. Such a schedule may include a deposit prior to the start of work. There may also be a temporary 'retainer' (5- 10% of the total cost of the job) at the end of the contract for correcting any small items which have not been completed or repaired.
Pedestal	A metal box installed at various locations along utility easements that contain electrical, telephone, or cable television switches and connections.
Penalty clause	A provision in a contract that provides for a reduction in the amount otherwise payable under a contract to a contractor as a penalty for failure to meet deadlines or for failure of the project to meet contract specifications.
Penny	As applied to nails, it originally indicated the price per hundred. The term now series as a measure of nail length and is abbreviated by the letter "d". Normally, 16d (16 "penny") nails are used for framing
Percolation test or perc. test	Tests that a soil engineer performs on earth to determine the feasibility of installing a leech field type sewer system on a lot. A test to determine if the soil on a proposed building lot is capable of absorbing the liquid affluent from a septic system.
Performance bond	An amount of money (usually 10% of the total price of a job)  that a contractor must put on deposit with a governmental agency as an insurance policy that guarantees the contractors' proper and timely completion of a project or job.
Perimeter drain	3" or 4" perforated plastic pipe that goes around the perimeter (either inside or outside) of a foundation wall (before backfill) and collects and diverts ground water away from the foundation. Generally, it is "daylighted" into a sump pit inside the home, and a sump pump is sometimes inserted into the pit to discharge any accumulation of water.
Permeability	A measure of the ease with which water penetrates a material.
Permit	A governmental municipal authorization to perform a building process as in: · Zoning\Use permit - Authorization to use a property for a specific use e.g. a garage, a single family residence etc. · Demolition permit  Authorization to tear down and remove an existing structure. · Grading permit  Authorization to change the contour of the land. · Septic permit  A health department authorization to build or modify a septic system. · Building permit  Authorization to build or modify a structure. · Electrical permit  A separate permit required for most electrical work. · Plumbing permit  A separate permit required for new plumbing and larger modifications of existing plumbing systems.
Pigtails, electrical	The electric cord that the electrician provides and installs on an appliance such as a garbage disposal, dishwasher, or range hood.
Pier	A column of masonry, usually rectangular in horizontal cross section, used to support other structural members. Also see Caisson.
Pigment	A powdered solid used in paint or enamel to give it a color.
Pilot hole	A small diameter, pre-drilled hole that guides a nail or screw.
Pilot light	A small, continuous flame (in a hot water heater, boiler, or furnace) that ignites gas or oil burners when needed.
Pitch	The incline slope of a roof or the ratio of the total rise to the total width of a house, i.e., a 6-foot rise and 24 - foot width is a one fourth pitch roof. Roof slope is expressed in the inches of rise, per foot of horizontal run.
PITI	Principal, interest, taxes and insurance (the four major components of monthly housing payments).
Plan view	Drawing of a structure with the view from overhead, looking down.
Plate	Normally a 2 X 4 or 2 X 6 that lays horizontally within a framed structure, such as:
Sill plate	A horizontal member anchored to a concrete or masonry wall.
Sole plate	Bottom horizontal member of a frame wall.
Top plate	Top horizontal member of a frame wall supporting ceiling joists, rafters, or other members.
Plenum	The main hot air supply duct leading from a furnace.
Plot plan	An overhead view plan that shows the location of the home on the lot. Includes all easements, property lines, set backs, and legal descriptions of the home. Provided by the surveyor.
Plough, plow	To cut a lengthwise groove in a board or plank. An exterior handrail normally has a ploughed groove for hand gripping purposes
Plumb	Exactly vertical and perpendicular.
Plumb bob	A lead weight attached to a string. It is the tool used in determining plumb.
Plumbing boots	Metal saddles used to strengthen a bearing wall/vertical stud(s) where a plumbing drain line has been cut through and installed.
Plumbing ground	The plumbing drain and waste lines that are installed beneath a basement floor.
Plumbing jacks	Sleeves that fit around drain and waste vent pipes at, and are nailed to, the roof sheeting.
Plumbing rough	Work performed by the plumbing contractor after the Rough Heat is installed. This work includes installing all plastic ABS drain and waste lines, copper water lines, bath tubs, shower pans, and gas piping to furnaces and fireplaces. Lead solder should not be used on copper piping.
Plumbing stack	A plumbing vent pipe that penetrates the roof.
Plumbing trim	Work performed by the plumbing contractor to get the home ready for a final plumbing inspection. Includes installing all toilets (water closets), hot water heaters, sinks, connecting all gas pipe to appliances, disposal, dishwasher, and all plumbing items.
Plumbing waste line	Plastic pipe used to collect and drain sewage waste.
Ply	A term to denote the number of layers of roofing felt, veneer in plywood, or layers in built  up materials, in any finished piece of such material.
Plywood	A panel (normally 4' X 8') of wood made of three or more layers of veneer, compressed and joined with glue, and usually laid with the grain of adjoining plies at right angles to give the sheet strength.
Point load	A point where a bearing/structural weight is concentrated and transferred to the foundation.
Portland cement	Cement made by heating clay and crushed limestone into a brick and then grinding to a pulverized powder state.
Post	A vertical framing member usually designed to carry a beam. Often a 4" x 4", a 6" x 6", or a metal pipe with a flat plate on top and bottom.
Post and Beam	A basic building method that uses just a few hefty posts and beams to support an entire structure. Contrasts with stud framing.
Power vent	A vent that includes a fan to speed up air flow.  Often installed on roofs.
Premium	Amount payable on a loan.
Preservative	. Any pesticide substance that, for a reasonable length of time, will prevent the action of wood - destroying fungi, insect borers, and similar destructive agents when the wood has been properly coated or impregnated with it. Normally an arsenic derivative. Chromated Copper Arsenate (CCA) is an example.
Pressure Relief Valve (PRV)	A device mounted on a hot water heater or boiler which is designed to release any high steam pressure in the tank to prevent tank explosions.
Pressure Treated Wood	Lumber that has been saturated with a preservative.
Primer	The first, base coat of paint when a paint job consists of two or more coats. A first coating formulated to seal raw surfaces and holding succeeding finish coats.
Principal	The original amount of the loan, the capital.
Property survey	A survey to determine the boundaries of your property. The cost depends on the complexity of the survey.
P trap	Curved, "U" section of drain pipe that holds a water seal to prevent sewer gasses from entering the home through a fixtures water drain.
Pump mix	Special concrete that will be used in a concrete pump. Generally, the mix has smaller rock aggregate than regular mix.
Punch list	A list of discrepancies that need to be corrected by the contractor.
Punch out	To inspect and make a discrepancy list.
Putty	A type of dough used in sealing glass in the sash, filling small holes and crevices in wood, and for similar purposes.
PVC or CPVC	Poly Vinyl Chloride -A type of white or light gray plastic pipe sometimes used for water supply lines and waste pipe.

Back to top

Q

 

Quarry tile	A man made or machine made clay tile used to finish a floor or wall. Generally 6" X  6"  X 1/4" thick .
Quarter round	A small trim molding that has the cross section of a quarter circle.

Back to top

R

 

Rabbet	A rectangular longitudinal groove cut in the corner edge of a board or plank.
Radiant heating	A method of heating, usually consisting of a forced hot water system with pipes placed in the floor, wall, or ceiling. Also electrically heated panels.
Radiation	Energy transmitted from a heat source to the air around it. Radiators actually depend more on convection than radiation.
Radon	A naturally occurring, heavier than air, radioactive gas common in many parts of the country.  Radon gas exposure is associated with lung cancer. Mitigation measures may involve crawl space and basement venting and various forms of vapor barriers.
Radon system	A ventilation system beneath the floor of a basement and/or structural wood floor and designed to fan exhaust radon gas to the outside of the home
Rafter	Lumber used to support the roof sheeting and roof loads. Generally, 2 X 10's and 2 X 12's are used. The rafters of a flat roof are sometimes called roof joists.
Rafter, hip	A rafter that forms the intersection of an external roof angle.
Rafter, valley	A rafter that forms the intersection of an internal roof angle. The valley rafter is normally made of double 2 inch thick members.
Rail	Cross members of panel doors or of a sash. Also, a wall or open balustrade placed at the edge of a staircase, walkway bridge, or elevated surface to prevent people from falling off.  Any relatively lightweight horizontal element, especially those found in fences (split rail).
Railroad tie	Black, tar and preservative impregnated, 6" X 8" and 6' - 8' long wooden timber that was used to hold railroad track in place. Normally used as a member of a retaining wall.
Rake	Slope or slanted.
Rake fascia	The vertical face of the sloping end of a roof eave.
Rake siding	The practice of installing lap siding diagonally
Ranch	A single story, one level home.
Ready mixed concrete	Concrete mixed at a plant or in trucks en route to a job and delivered ready for placement.
Rebar, reinforcing bar	Ribbed steel bars installed in foundation concrete walls, footers, and poured in place concrete structures designed to strengthen concrete. Comes in various thickness' and strength grade.
Receptacle	An electrical outlet.  A typical household will have many 120 volt receptacles for plugging in lams and appliances and 240 volt receptacles for the range, clothes dryer, air conditioners, etc.
Recording fee	A charge for recording the transfer of a property, paid to a city, county, or other appropriate branch of government.
Redline, red lined prints	Blueprints that reflect changes and that are marked with red pencil.
Reducer	A fitting with different size openings at either end and used to go from a larger to a smaller pipe.
Reflective insulation	Sheet material with one or both faces covered with aluminum foil.
Refrigerant	A substance that remains a gas at low temperatures and pressure and can be used to transfer heat. Freon is an example and is used in air conditioning systems.
Register	A grill placed over a heating duct or cold air return.
Reglaze	To replace a broken window.
Relief valve	A device designed to open if it detects excess temperature or pressure.
Remote	Remote electrical, gas, or water meter digital readouts that are installed near the front of the home in order for utility companies to easily read the home owners usage of the service.
Retaining wall	A structure that holds back a slope and prevents erosion.
Retentions	Amounts withheld from progress billings until final and satisfactory project completion.
R factor or value	A measure of a materials resistance to the passage of heat. New homewalls are usually insulated with 4" of batt insulation with an R value of R-13, and a ceiling insulation of R-30.
Ribbon (girt)	Normally a 1 X 4 board let into the studs horizontally to support the ceiling or second floor joists.
Ridge	The horizontal line at the junction of the top edges of two sloping roof surfaces.
Ridge board	The board placed on the ridge of the roof onto which the upper ends of other rafters are fastened.
Ridge shingles	Shingles used to cover the ridge board.
Rim joist	A joist that runs around the perimeter of the floor joists and home.
Rise	The vertical distance from the eaves line to the ridge. Also the vertical distance from stair tread to stair tread (and not to exceed 7 ½").
Riser	Each of the vertical boards closing the spaces between the treads of stairways.
Riser and panel	The exterior vertical pipe (riser) and metal electric box (panel) the electrician provides and installs at the "Rough Electric" stage.
Road base	A aggregate mixture of sand and stone.
Rock 1, 2, 3	When referring to drywall, this means to install drywall to the walls and ceilings (with nails and screws), and before taping is performed.
Roll, rolling	To install the floor joists or trusses in their correct place. (To "roll the floor" means to install the floor joists).
Romex	A name brand of nonmetallic sheathed electrical cable that is used for indoor wiring.
Roll roofing	Asphalt roofing products manufactured in roll form. 36 inch wide rolls with and 108 square feet of material. Weights are generally 45 to 90 pounds per roll.
Romex	A name brand of nonmetallic sheathed electrical cable that is used for indoor wiring.
Roof jack	Sleeves that fit around the black plumbing waste vent pipes at, and are nailed to, the roof sheeting.
Roof joist	The rafters of a flat roof. Lumber used to support the roof sheeting and roof loads. Generally, 2 X 10's and 2 X 12's are used.
Roof sheathing or sheeting	The wood panels or sheet material fastened to the roof rafters or trusses on which the shingle or other roof covering is laid.
Roof valley	The "V" created where two sloping roofs meet.
Rough opening	The horizontal and vertical measurement of a window or door opening before drywall or siding is installed.
Rough sill	The framing member at the bottom of a rough opening for a window. It is attached to the cripple studs below the rough opening.
Roughing-in	The initial stage of a plumbing, electrical, heating, carpentry, and/or other project, when all components that won't be seen after the second finishing phase are assembled. See also Heat Rough, Plumbing Rough, and Electrical Rough.
Run, roof	The horizontal distance from the eaves to a point directly under the ridge. One half the span.
Run, stair	the horizontal distance of a stair tread from the nose to the riser.
R Value	A measure of insulation. A measure of a materials resistance to the passage of heat. The higher the R value, the more insulating "power" it has. For example, typical new home's walls are usually insulated with 4" of batt insulation with an R value of R -13, and a ceiling insulation of R - 30

Back to top

S

 

Saddle	A small second roof built behind the back side of a fireplace chimney to divert water around the chimney. Also, the plate at the bottom of some—usually exterior—door openings. Sometimes called a threshold.
Sack mix	The amount of Portland cement in a cubic yard of concrete mix. Generally, 5 or 6 sack is required in a foundation wall.
Sales contract	A contract between a buyer and seller which should explain: (1) What the purchase includes, (2) What guarantees there are, (3) When the buyer can move in, (4) What the closing costs are, and (5) What recourse the parties have if the contract is not fulfilled or if the buyer cannot get a mortgage commitment at the agreed upon time.
Sand float finish	Lime that is mixed with sand, resulting in a textured finish on a wall.
Sanitary sewer	A sewer system designed for the collection of waste water from the bathroom, kitchen and laundry drains, and is usually not designed to handle storm water.
Sash	A single light frame containing one or more lights of glass. The frame that holds the glass in a window, often the movable part of the window.
Sash balance	A device, usually operated by a spring and designed to hold a single hung window vent up and in place
Saturated felt	A felt which is impregnated with tar or asphalt.
Schedule (window, door, mirror)	A table on the blueprints that list the sizes, quantities and locations of the windows, doors and mirrors.
Scrap out	The removal of all drywall material and debris after the home is "hung out" (installed) with drywall.
Scratch coat	The first coat of plaster, which is scratched to form a bond for a second coat.
Screed, concrete	To level off concrete to the correct elevation during a concrete pour.
Screed, plaster	A small strip of wood, usually the thickness of the plaster coat, used as a guide for plastering.
Scribing	Cutting and fitting woodwork to an irregular surface.
Scupper	(1) An opening for drainage in a wall, curb or parapet. (2) The drain in a downspout or flat roof, usually connected to the downspout.
Sealer	A finishing material, either clear or pigmented, that is usually applied directly over raw wood for the purpose of sealing the wood surface.
Seasoning	Drying and removing moisture from green wood in order to improve its usability.
Self-Sealing Shingles	Shingles containing factory applied strips or spots of self- sealing adhesive.
Semigloss paint or enamel	A paint or enamel made so that its coating, when dry, has some luster but is not very glossy. Bathrooms and kitchens are normally painted semi-gloss
Septic system	An on site waste water treatment system. It usually has a septic tank which promotes the biological digestion of the waste, and a drain field which is designed to let the left over liquid soak into the ground. Septic systems and permits are usually sized by the number of bedrooms in a house.
Service entrance panel	Main power cabinet where electricity enters a home wiring system.
Service equipment	Main control gear at the service entrance, such as circuit breakers, switches, and fuses.
Service lateral	Underground power supply line.
Setback Thermostat	A thermostat with a clock which can be programmed to come on or go off at various temperatures and at different times of the day/week. Usually used as the heating or cooling system thermostat.
Settlement	Shifts in a structure, usually caused by freeze-thaw cycles underground.
Sewage ejector	A pump used to 'lift' waste water to a gravity sanitary sewer line. Usually used in basements and other locations which are situated bellow the level of the side sewer.
Sewer lateral	The portion of the sanitary sewer which connects the interior waste water lines to the main sewer lines. The side sewer is usually buried in several feet of soil and runs from the house to the sewer line. It is usually 'owned' by the sewer utility, must be maintained by the owner and may only be serviced by utility approved contractors. Sometimes called side sewer.
Sewer stub	The junction at the municipal sewer system where the home's sewer line is connected.
Sewer tap	The physical connection point where the home's sewer line connects to the main municipal sewer line.
Shake	A wood roofing material, normally cedar or redwood. Produced by splitting a block of the wood along the grain line. Modern shakes are sometimes machine sawn on one side. See shingle.
Shear block	Plywood that is face nailed to short (2 X 4's or 2 X 6's) wall studs (above a door or window, for example). This is done to prevent the wall from sliding and collapsing.
Sheathing, sheeting	The structural wood panel covering, usually OSB or plywood, used over studs, floor joists or rafters/trusses of a structure.
Shed roof	A roof containing only one sloping plane.
Sheet metal work	All components of a house employing sheet metal, such as flashing, gutters, and downspouts.
Sheet metal duct work	The heating system. Usually round or rectangular metal pipes and sheet metal (for Return Air) and installed for distributing warm (or cold) air from the furnace to rooms in the home.
Sheet Rock  Drywall Wall board or gypsum	A manufactured panel made out of gypsum plaster and encased in a thin cardboard. Usually 1/2" thick and 4' x 8' or 4' x 12' in size. The 'joint compound'. 'Green board' type drywall has a greater resistance to moisture than regular (white) plasterboard and is used in bathrooms and other "wet areas".
Shim	A small piece of scrap lumber or shingle, usually wedge shaped, which when forced behind a furring strip or framing member forces it into position. Also used when installing doors and placed between the door jamb legs and 2 X 4 door trimmers. Metal shims are wafer  1 1/2" X 2" sheet metal of various thickness' used to fill gaps in wood framing members, especially at bearing point locations.
Shingles	Roof covering of asphalt. asbestos, wood, tile, slate, or other material cut to stock lengths, widths, and thickness'.
Shingles, siding	Various kinds of shingles, used over sheathing for exterior wall covering of a structure.
Short circuit	A situation that occurs when hot and neutral wires come in contact with each other. Fuses and circuit breakers protect against fire that could result from a short.
Shutter	Usually lightweight louvered decorative frames in the form of doors located on the sides of a window. Some shutters are made to close over the window for protection.
Side sewer	The portion of the sanitary sewer which connects the interior waste water lines to the main sewer lines. The side sewer is usually buried in several feet of soil and runs from the house to the sewer line. It is usually 'owned' by the sewer utility, must be maintained by the owner and may only be serviced by utility approved contractors. Sometimes called sewer lateral.
Siding	The finished exterior covering of the outside walls of a frame building.
Siding, (lap siding)	Slightly wedge shaped boards used as horizontal siding in a lapped pattern over the exterior sheathing. Varies in butt thickness from ½ to ¾ inch and in widths up to 12".
Sill	(1) The 2 X 4 or 2 X 6 wood plate framing member that lays flat against and bolted to the foundation wall (with anchor bolts) and upon which the floor joists are installed. Normally the sill plate is treated lumber. (2) The member forming the lower side of an opening, as a door sill or window sill.
Sill cock	An exterior water faucet (hose bib).
Sill plate (mudsill)	Bottom horizontal member of an exterior wall frame which rests on top a foundation, sometimes called mudsill. Also sole plate, bottom member of an interior wall frame.
Sill seal	Fiberglass or foam insulation installed between the foundation wall and sill (wood) plate. Designed to seal any cracks or gaps.
Single hung window	A window with one vertically sliding sash or window vent.
Skylight	A more or less horizontal window located on the roof of a building.
Slab, concrete	Concrete pavement, i.e. driveways, garages, and basement floors.
Slab, door	A rectangular door without hinges or frame.
Slab on grade	A type of foundation with a concrete floor which is placed directly on the soil. The edge of the slab is usually thicker and acts as the footing for the walls.
Slag	Concrete cement that sometimes covers the vertical face of the foundation void material.
Sleeper	Usually, a wood member embedded in concrete, as in a floor, that serves to support and to fasten the subfloor or flooring.
Sleeve(s)	Pipe installed under the concrete driveway or sidewalk, and that will be used later to run sprinkler pipe or low voltage wire.
Slope	The incline angle of a roof surface, given as a ratio of the rise (in inches) to the run (in feet). See also pitch.
Slump	The "wetness" of concrete. A 3 inch slump is dryer and stiffer than a 5 inch slump.
Soffit	The area below the eaves and overhangs. The underside where the roof overhangs the walls. Usually the underside of an overhanging cornice.
Soil pipe	A large pipe that carries liquid and solid wastes to a sewer or septic tank.
Soil stack	A plumbing vent pipe that penetrates the roof.
Sole plate	The bottom, horizontal framing member of a wall that's attached to the floor sheeting and vertical wall studs.
Solid bridging	A solid member placed between adjacent floor joists near the center of the span to prevent joists or rafters from twisting.
Sonotube	Round, large cardboard tubes designed to hold wet concrete in place until it hardens.
Sound attenuation	Sound proofing a wall or subfloor, generally with fiberglass insulation.
Space heat	Heat supplied to the living space, for example, to a room or the living area of a building.
Spacing	The distance between individual members or shingles in building construction.
Span	The clear distance that a framing member carries a load without support between structural supports. The horizontal distance from eaves to eaves.
Spec home	A house built before it is sold. The builder speculates that he can sell it at a profit.
Specifications or Specs	A narrative list of materials, methods, model numbers, colors, allowances, and other details which supplement the information contained in the blue prints. Written elaboration in specific detail about construction materials and methods. Written to supplement working drawings.
Splash block	Portable concrete (or vinyl) channel generally placed beneath an exterior sill cock (water faucet) or downspout in order to receive roof drainage from downspouts and to divert it away from the building.
Square	A unit of measure 100 square feet usually applied to roofing and siding material. Also, a situation that exists when two elements are at right angles to each other. Also a tool for checking this.
Square-tab shingles	Shingles on which tabs are all the same size and exposure.
Squeegie	Fine pea gravel used to grade a floor (normally before concrete is placed).
Stack (trusses)	To position trusses on the walls in their correct location.
Standard practices of the trade(s)	One of the more common basic and minimum construction standards. This is another way of saying that the work should be done in the way it is normally done by the average professional in the field.
Starter strip	Asphalt roofing applied at the eaves that provides protection by filling in the spaces under the cutouts and joints of the first course of shingles.
Stair carriage or stringer	Supporting member for stair treads. Usually a 2 X 12 inch plank notched to receive the treads; sometimes called a "rough horse."
Stair landing	A platform between flights of stairs or at the termination of a flight of stairs. Often used when stairs change direction. Normally no less than 3 ft. X 3 ft. square.
Stair rise	The vertical distance from stair tread to stair tread (and not to exceed 7 ½").
Static vent	A vent that does not include a fan.
STC (Sound Transmission Class)	The measure of sound stopping of ordinary noise.
Steel inspection	A municipal and/or engineers inspection of the concrete foundation wall, conducted before concrete is poured into the foundation panels. Done to insure that the rebar (reinforcing bar), rebar nets, void material, beam pocket plates, and basement window bucks are installed and wrapped with rebar and complies with the foundation plan.
Step flashing	Flashing application method used where a vertical surface meets a sloping roof plane. 6" X 6" galvanized metal bent at a 90 degree angle, and installed beneath siding and over the top of shingles. Each piece overlaps the one beneath it the entire length of the sloping roof (step by step).
Stick built	A house built without prefabricated parts. Also called conventional building.
Stile	An upright framing member in a panel door.
Stool	The flat molding fitted over the window sill between jambs and contacting the bottom rail of the lower sash.  Also another name for toilet.
Stop box	Normally a cast iron pipe with a lid (@ 5" in diameter) that is placed vertically into the ground, situated near the water tap in the yard, and where a water cut off valve to the home is located (underground). A long pole with a special end is inserted into the curb stop to turn off/on the water.
Stop Order	A formal, written notification to a contractor to discontinue some or all work on a project for reasons such as safety violations, defective materials or workmanship, or cancellation of the contract.
Stops	Moldings along the inner edges of a door or window frame. Also valves used to shut off water to a fixture.
Stop valve	A device installed in a water supply line, usually near a fixture, that permits an individual to shut off the water supply to one fixture without interrupting service to the rest of the system.
Storm sash or storm window	. An extra window usually placed outside of an existing one, as additional protection against cold weather.
Storm sewer	A sewer system designed to collect storm water and is separated from the waste water system.
Story	That part of a building between any floor or between the floor and roof.
Strike	The plate on a door frame that engages a latch or dead bolt.
String, stringer	A timber or other support for cross members in floors or ceilings. In stairs, the supporting member for stair treads. Usually a 2 X 12 inch plank notched to receive the treads
Strip flooring	Wood flooring consisting of narrow, matched strips.
Structural floor	A framed lumber floor that is installed as a basement floor instead of concrete. This is done on very expansive soils.
Stub, stubbed	To push through.
Stucco	Refers to an outside plaster finish made with Portland cement as its base.
Stud	A vertical wood framing member, also referred to as a wall stud, attached to the horizontal sole plate below and the top plate above. Normally 2 X 4's or 2 X 6's, 8' long (sometimes 92 5/8"). One of a series of wood or metal vertical structural members placed as supporting elements in walls and partitions.
Stud framing	A building method that distributes structural loads to each of a series of relatively lightweight studs. Contrasts with post and beam.
Stud shoe	A metal, structural bracket that reinforces a vertical stud. Used on an outside bearing wall where holes are drilled to accommodate a plumbing waste line.
Subfloor	The framing components of a floor to include the sill plate, floor joists, and deck sheeting over which a finish floor is to be laid.
Sump	Pit or large plastic bucket/barrel inside the home designed to collect ground water from a perimeter drain system.
Sump pump	A submersible pump in a sump pit that pumps any excess ground water to the outside of the home.
Suspended ceiling	A ceiling system supported by hanging it from the overhead structural framing.
Sway brace	Metal straps or wood blocks installed diagonally on the inside of a wall from bottom to top plate, to prevent the wall from twisting, racking, or falling over "domino" fashion.
Switch	A device that completes or disconnects an electrical circuit.

Back to top

T

 

T & G, tongue and groove	A joint made by a tongue (a rib on one edge of a board) that fits into a corresponding groove in the edge of another board to make a tight flush joint. Typically, the sub-floor plywood is T & G.
Tab	The exposed portion of strip shingles defined by cutouts.
Tail beam	A relatively short beam or joist supported in a wall on one end and by a header at the other.
Take off	The material necessary to complete a job.
Taping	The process of covering drywall joints with paper tape and joint compound.
T bar	Ribbed, "T" shaped bars with a flat metal plate at the bottom that are driven into the earth. Normally used chain link fence poles, and to mark locations of a water meter pit.
Teco	Metal straps that are nailed and secure the roof rafters and trusses to the top horizontal wall plate. Sometimes called a hurricane clip.
Tee	A "T" shaped plumbing fitting.
Tempered	Strengthened. Tempered glass will not shatter nor create shards, but will "pelletize" like an automobile window. Required in tub and shower enclosures and locations, entry door glass and sidelight glass, and in a windows when the window sill is less than 16" to the floor.
Termites	Wood eating insects that superficially resemble ants in size and general appearance, and live in colonies.
Termite shield	A shield, usually of galvanized metal, placed in or on a foundation wall or around pipes to prevent the passage of termites.
Terra cotta	A ceramic material molded into masonry units.
Thermoply ™	Exterior laminated sheathing nailed to the exterior side of the exterior walls. Normally ¼ " thick, 4 X 8 or 4 x 10 sheets with an aluminumized surface.
Thermostat	A device which relegates the temperature of a room or building by switching heating or cooling equipment on or off.
Thinner	Another name for the heating contractor.
Three-Dimensional shingles	Laminated shingles. Shingles that have added dimensionality because of extra layers or tabs, giving a shake- like appearance. May also be called "architectural shingles".
Threshold	The bottom metal or wood plate of an exterior door frame. Generally they are adjustable to keep a tight fit with the door slab.
Time and materials contract	A construction contract which specifies a price for different elements of the work such as cost per hour of labor, overhead, profit, etc. A contract which may not have a maximum price, or may state a 'price not to exceed'.
Tip up	The downspout extension that directs water (from the home's gutter system) away from the home. They typically swing up when mowing the lawn, etc.
Title	Evidence (usually in the form of a certificate or deed) of a person's legal right to ownership of a property.
TJI or TJ	Manufactured structural building component resembling the letter "I". Used as floor joists and rafters. I- joists include two key parts: flanges and webs. The flange or from of the I joist may be made of laminated veneer lumber or dimensional lumber, usually formed into a 1 ½" width. The web or center of the I-joist is commonly made of plywood or oriented strand board (OSB). Large holes can be cut in the web to accommodate duct work and plumbing waste lines. I-joists are available in lengths up to 60'' long.
Toenailing	To drive a nail in at a slant. Method used to secure floor joists to the plate.
Top chord	The upper or top member of a truss.
Top plate	Top horizontal member of a frame wall supporting ceiling joists, rafters, or other members.
Transmitter (garage door)	The small, push button device that causes the garage door to open or close.
Trap	A plumbing fitting that holds water to prevent air, gas, and vermin from backing up into a fixture.
Tread	The walking surface board in a stairway on which the foot is placed.
Treated lumber	A wood product which has been impregnated with chemical pesticides such as CCA (Chromated Copper Arsenate) to reduce damage from wood rot or insects. Often used for the portions of a structure which are likely to be in contact with soil and water. Wood may also be treated with a fire retardant.
Trim (plumbing, heating, electrical)	The work that the "mechanical" contractors perform to finish their respective aspects of work, and when the home is nearing completion and occupancy.
Trim-Interior	The finish materials in a building, such as moldings applied around openings (window trim, door trim) or at the floor and ceiling of rooms (baseboard, cornice, and other moldings). Also, the physical work of installing interior doors and interior woodwork, to include all handrails, guardrails, stair way balustrades, mantles, light boxes, base, door casings, cabinets, countertops, shelves, window sills and aprons, etc.
Trim-Exterior	The finish materials on the exterior of a building, such as moldings applied around openings (window trim, door trim), siding, windows, exterior doors, attic vents, crawl space vents, shutters, etc. Also, the physical work of installing these materials .
Trimmer	The vertical stud that supports a header at a door, window, or other opening.
Truss	An engineered and manufactured roof support member with "zig- zag" framing members. Does the same job as a rafter but is designed to have a longer span than a rafter.
Tub trap	Curved, "U" shaped section of a bath tub drain pipe that holds a water seal to prevent sewer gasses from entering the home through tubs water drain.
Turnkey	A term used when the subcontractor provides all materials (and labor) for a job.
Turpentine	A petroleum, volatile oil used as a thinner in paints and as a solvent in varnishes.

 

Back to top

U

 

UL (Underwriters' Laboratories)	An independent testing agency that checks electrical devices and other components for possible safety hazards.
Undercoat	A coating applied prior to the finishing or top coats of a paint job. It may be the first of two or the second of three coats. Sometimes called the Prime coat.
Underground plumbing	The plumbing drain and waste lines that are installed beneath a basement floor.
Underlayment	A ¼" material placed over the subfloor plywood sheeting and under finish coverings, such as vinyl flooring, to provide a smooth, even surface. Also a secondary roofing layer that is waterproof or water-resistant, installed on the roof deck and beneath shingles or other roof finishing layer.
Union	A plumbing fitting that joins pipes end-to-end so they can be dismantled.
Utility Easement	The area of the earth that has electric, gas, or telephone lines. These areas may be owned by the homeowner, but the utility company has the legal right to enter the area as necessary to repair or service the lines

Back to top

V

 

Valley	The "V" shaped area of a roof where two sloping roofs meet. Water drains off the roof at the valleys.
Valley flashing	Sheet metal that lays in the "V" area of a roof valley.
Valuation	An inspection carried out for the benefit of the mortgage lender to ascertain if a property is a good security for a loan.
Valuation fee	The fee paid by the prospective borrower for the lender's inspection of the property. Normally paid upon loan application.
Vapor barrier	A building product installed on exterior walls and ceilings under the drywall and on the warm side of the insulation. It is used to retard the movement of water vapor into walls and prevent condensation within them. Normally, polyethylene plastic sheeting is used.
Variable rate	An interest rate that will vary over the term of the loan.
Veneer	Extremely thin sheets of wood. Also a thin slice of wood or brick or stone covering a framed wall.
Vent	A pipe or duct which allows the flow of air and gasses to the outside. Also, another word for the moving glass part of a window sash, i.e. window vent.
Vermiculite	A mineral used as bulk insulation and also as aggregate in insulating and acoustical plaster and in insulating concrete floors.
Veterans Administration (VA)	A federal agency that insures mortgage loans with very liberal down payment requirements for honorably discharged veterans and their surviving spouses.
Visqueen	A 4 mil or 6 mil plastic sheeting.
Void	Cardboard rectangular boxes that are installed between the earth (between caissons) and the concrete foundation wall. Used when expansive soils are present.
Voltage	A measure of electrical potential. Most homes are wired with 110 and 220 volt lines. The 110 volt power is used for lighting and most of the other circuits. The 220 volt power is usually used for the kitchen range, hot water heater and dryer

Back to top

W

 

Wafer board	A manufactured wood panel made out of 1" to 2" wood chips and glue. Often used as a substitute for plywood in the exterior wall and roof sheathing.
Walk-Through	A final inspection of a home before "Closing" to look for and document problems that need to be corrected.
Wall out	When a painter pray paints the interior of a home.
Warping	Any distortion in a material.
Warranty	In construction there are two general types of warranties. One is provided by the manufacturer of a product such as roofing material or an appliance. The second is a warranty for the labor. For example, a roofing contract may include a 20 year material warranty and a 5 year labor warranty. Many new homebuilders provide a one year warranty. Any major issue found during the first year should be communicated to the builder immediately. Small items can be saved up and presented to the builder for correction periodically through the first year after closing.
Waste pipe and vent	Plumbing plastic pipe that carries waste water to the municipal sewage system.
Water board	Water resistant drywall to be used in tub and shower locations. Normally green or blue colored
Water closet	Another name for toilet.
Water meter pit (or vault)	The box /cast iron bonnet and concrete rings that contains the water meter.
Water-Repellent preservative	A liquid applied to wood to give the wood water repellant properties
Water table	The location of the underground water, and the vertical distance from the surface of the earth to this underground water.
Water tap	The connection point where the home water line connects to the main municipal water system.
W C	An abbreviation for water closet (toilet).
Weatherization	Work on a building exterior in order to reduce energy consumption for heating or cooling.  Work involving adding insulation, installing storm windows and doors, caulking cracks and putting on weather-stripping.
Weatherstrip	Narrow sections of thin metal or other material installed to prevent the infiltration of air and moisture around windows and doors.
Weep holes	Small holes in storm window frames that allow moisture to escape.
Whole house fan	A fan designed to move air through and out of a home and normally installed in the ceiling.
Wind bracing	Metal straps or wood blocks installed diagonally on the inside of a wall from bottom to top plate, to prevent the wall from twisting, racking, or falling over "domino" fashion.
Window buck	Square or rectangular box that is installed within a concrete foundation or block wall. A window will eventually be installed in this "buck" during the siding stage of construction
Window frame	The stationary part of a window unit; window sash fits into the window frame.
Window sash	The operating or movable part of a window; the sash is made of window panes and their  border.
Wire nut	A plastic device used to connect bare wires together.
Wonderboard ™	A panel made out of concrete and fiberglass usually used as a ceramic tile backing material. Commonly used on bathtub decks.
Wrapped drywall	Areas that get complete drywall covering, as in the doorway openings of bifold and bipass closet doors.

Back to top

Y

 

Y	A "Y" shaped plumbing fitting.
Yard of concrete	One cubic yard of concrete is 3' X 3' X 3' in volume, or 27 cubic feet.  One cubic yard of concrete will pour 80 square feet of 3 ½" sidewalk or basement/garage floor.
Yoke	The location where a home's water meter is sometimes installed between two copper pipes, and located in the water meter pit in the yard

Back to top

Z

 

Z-bar flashing	Bent, galvanized metal flashing that's installed above a horizontal trim board of an exterior window, door, or brick run. It prevents water from getting behind the trim/brick and into the home.
Zone	The section of a building that is served by one heating or cooling loop because it has noticeably distinct heating or cooling needs. Also, the section of property that will be watered from a lawn sprinkler system.
Zone valve	A device, usually placed near the heater or cooler, which controls the flow of water or steam to parts of the building; it is controlled by a zone thermostat.
Zoning	A governmental process and specification which limits the use of a property e.g. single family use, high rise residential use, industrial use, etc. Zoning laws may limit where you can locate a structure. Also see building codes.

Back to top